Home page
Links to other sites
SPEEDEX History
SPEEDEX Parts
SPEEDEX’s and their owners
SPEEDEX advertising etc from the ‘50s & ‘60s
Where are they now?
For Sale and Wants
Stupendous 750
Special Builders Guide
Independent front suspensions
S U P P L I E D B Y
S P E E D E X
L U T O N
By the 1950’s the Austin beam axle was an old design with limitations even when modified into a lowered sports shape. Independent suspension units were fashionable in the ‘50’s both on new cars and as something to add to your special. Unfortunately they work best on a very rigid chassis, not something the Austin 7 chassis is renown for. However if you wanted your car to reflect the ethos of the time, this was the thing to have.
A wider steering cross tube is used with the wider axle. It was also threaded to take Ford 10 track rod ends to cope with the articulation of each separate side—the A7 ones won’t work with this set up. The Cambridge IFS has a straight cross tube with a different (and as yet unidentified) set of track rod ends. The steering arms had to be taper bored to take the tapered fixing. They can fit in either side, the correct way is with them inclined downwards and pointing in towards the chassis, the track rod end tapers then enter from the bottom all of which lowers the cross tube so it doesn’t foul on the chassis. You’ll probably notice that the IFS cross tube has less of a down sweep in the centre for this reason. You can tell if they’re on the right way round from the little square ‘stop’ on each arm, it should butt up against the axle behind the king pin. Arms should be very tight in the stub axles, the offset of the track rod end can tend to rotate the steering arm in the stub axle. If necessary drill and tap through the stub axle just catching into the steering arm and fit a grub screw. Austin’s had a similar problem with their Sports models, these had lowered steering arms to match the lowered axle. However this produced a turning moment on them. Their solution was to cut small keyways in the stub axle with keys in the steering arms.
New Ford track rod ends can be obtained from Small Ford Spares
The most popular type was the Bowden twin spring type with two springs one above the other, the axle ends clamped between the ends. SPEEDEX like all the tuning firms produced their own version of the suspension unit. Their version only had one spring with two tubular arms forming the bottom joints, this followed a similar theme to an earlier Dante design. A Cambridge version was more complex and had a bottom spring and tubular arms as the top joints with special articulating radius arms back to the chassis side members near the rear of the engine. The scanned picture isn’t very sharp but you can just make out the top arms. Note the neat front shocker arrangement, it fits unobtrusively on the ‘conventional’ type A7 special. Those shockers are quite short!
IFS’s were available in two widths, standard 3’ 6” to fit underneath the wings of a standard car and a wider 3’ 10” to improve road holding on a special and giver a wider stance matching the width of a later back axle.
They all bolt onto the standard chassis in the same way with two U bolts but everything gets more complicated from there on. One thing to watch out for with the SPEEDEX type is the alignment of the bottom part to the top spring with the central bracket. They’re not a close fit together and you can end up with positive camber on one side and negative on the other. Slacken the U bolts and wiggle about until they’re the same both sides then retighten.
Bowden IFS with twin springs
SPEEDEX IFS with top spring and bottom links. Note the frame to mount shockers and the water pump
Cambridge IFS with bottom spring and short articulating radios arms. Note the chassis bracket to mount the top of the shockers.
IFS axles don’t have the holes for the Austin friction dampers so you have an alternative arrangement. It was normal to fit telescopic shock absorbers, Mini front ones make good replacements of the bulky Woodhead Munroe originals but a frame is needed to firmly anchor the shocker tops. I can help with a SPEEDEX type as in the picture above if you need one, one of the owners has sent me a dimensioned sketch. I also have one of the Bowden type frames so can help there too if you’re stuck. An alternative may be one of the twin friction brackets that are popular with A7 racers. These type of shocker is sized on the stroke between fully open to fully shut measuring between the centre of the eyes.
Cambridge Woodhead Munroe 8 1/2” to 11”
Bowden Woodhead Munroe 11 1/2” to 18 1/2”
Speedex ? ?
Mini fronts Various makes 8 1/2” to 11”
Some good news; although the king pins probably have a harder life in an IFS unit they’ve probably also had less years of abuse. I’ve never found one with a stretched axle eye as is so common on the standard axle beams. On the ones I’ve done, new pins are a good fit, maybe testimony to good accurate manufacture as well.
Radius arms will fit straight on for the standard width but the wider track one, which most seem to be, need two mounting balls spaced 4” apart, 2” either side of the centre of the cross member. However the rigid fixing between the radius arm and axle acts as a very stiff anti roll bar giving difficult steering characteristics. It’s better to have radius arms that articulate at both ends.